 |
|||
|
Page Title:
Table III. Thickness tolerances for ordered thickness 1/, inches (over and under) 2/. |
|
||
| ||||||||||
|
|  MIL-A-46100D (MR)
w/INT. AMENDMENT 2
TABLE III. Thickness tolerances for ordered thickness 1/, inches (over and under) 2/.
Tolerances over and under ordered thickness for widths given, inches
Specified
96 to
108 to
120 to
132 to
Thickness,
60 to
72 to
84 to
108
120
132
144
inches
To 60 72 excl. 84 excl. 96 excl.
excl.
excl.
excl.
incl.
1/8
2/
0.016
0.016
0.019
0.019
0.023
---
---
3/16
2/
0.016
0.016
0.019
0.019
0.023
---
---
1/4
2/
0.016
0.016
0.019
0.019
0.023
---
---
5/16
2/
0.016
0.019
0.019
0.019
0.023
0.026
---
3/8
2/
0.016
0.019
0.019
0.023
0.023
0.026
---
7/16
2/
0.016
0.019
0.019
0.023
0.026
0.026
0.031
1/2
2/
0.016
0.019
0.019
0.023
0.026
0.026
0.031
9/16
2/
0.019
0.019
0.019
0.023
0.026
0.031
0.031
5/8
2/
0.019
0.019
0.019
0.023
0.026
0.031
0.031
11/16
2/
0.019
0.019
0.019
0.023
0.026
0.031
0.031
3/4
2/
0.019
0.019
0.023
0.023
0.026
0.031
0.039
13/16
2/
0.023
0.023
0.023
0.026
0.031
0.031
0.039
7/8
2/
0.023
0.023
0.026
0.026
0.031
0.031
0.039
15/16
2/
0.023
0.023
0.026
0.026
0.031
0.036
0.043
1
2/
0.026
0.026
0.026
0.026
0.031
0.036
0.043
1-1/16
2/
0.026
0.026
0.026
0.031
0.031
0.036
0.043
1-1/8
2/
0.026
0.026
0.026
0.031
0.031
0.039
0.043
1-3/16
2/
0.031
0.031
0.031
0.031
0.036
0.043
0.048
1-1/4
2/
0.031
0.031
0.031
0.036
0.036
0.043
0.048
1-5/16
2/
0.031
0.031
0.031
0.036
0.036
0.043
0.053
1-3/8
2/
0.031
0.031
0.031
0.036
0.039
0.048
0.053
1-7/16
2/
0.036
0.036
0.036
0.036
0.043
0.048
0.058
1-1/2
2/
0.036
0.036
0.036
0.039
0.043
0.048
0.058
1-9/16
2/
0.036
0.036
0.036
0.039
0.043
0.058
0.058
1-5/8
2/
0.036
0.036
0.036
0.043
0.048
0.058
0.063
1-11/16
2/
0.039
0.039
0.039
0.043
0.048
0.058
0.063
1-3/4
2/
0.039
0.039
0.039
0.043
0.048
0.058
0.068
1-13/16
2/
0.043
0.043
0.043
0.048
0.053
0.058
0.068
1-7/8
2/
0.043
0.043
0.043
0.048
0.053
0.063
0.068
1-15/16
2/
0.043
0.043
0.043
0.048
0.053
0.063
0.076
2
2/
0.043
0.043
0.043
0.048
0.053
0.063
0.076
1/ For intermediate thickness, the tolerance of the closer specified gage shall apply. In case
of mid-point, the tolerance for lower gage or interpolated value shall apply.
2/ When plates under 60 inches are rolled double width, the equivalent wider plate
tolerance shall apply.
3.2.9.1.1 Depth of imperfections. The depth of rolled-in scale, scale pitting or snakes shall
not exceed 0.015 inch and shall not reduce the steel thickness below the allowable
minimum. Isolated individual pits over 0.015 inch deep but not over 0.03 inch deep and not
7
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals