Click here to make tpub.com your Home Page

Page Title: Acquisitions requirements
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Consolidation containers
Up
Pump Unit, Centrifugal, Diesel-Engine-Driven, 800 GPM at 1800 Feet Total Head
Next
Technical manuals



img
MIL-P-53108(ME)
f. Fasteners required of a and b, above, to attach material to the top of the skid mount
shall not interfere with the fasteners attaching the cover.
5.5.1.4 Electrolyte. The electrolyte, preserved as specified in 5.4, shall be packed
(2 fiberboard boxes) in a snug-fitting wooden container conforming to PPP-B-601, overseas
type. Blocking and bracing shall conform to MIL-STD-1186 and strapping shall be in
accordance with ASTM D 3953 and D 4675, type 1 or 2, grade l or 2.
5.5.2 Level C. Each pump unit, preserved as specified in 5.4, shall be packed in accordance
with MIL-STD-1190.
5.6 Marking. In addition to any special or other markings required of the contract or order
(see 6.2), each crate shall be marked in accordance with MIL-STD-129, including all appendices
as applicable for overseas shipment for use by a Military Command. Interior and exterior
packing lists are required in accordance with MIL-STD-129, appendix F. The packing list on the
outside of the crate shall be inserted in a moistureproof envelope and stapled to the side of the
crate. The envelope shall then be covered with a fiberboard cover stapled to the crate. The crate
surfaces on which markings are to be applied shall be prepared in accordance with
MIL-STD-129, appendix A. All markings shall be l-inch stencils, overcoated (weatherproofed)
with a clear coating compound. When the pump units are to be included as part of a set,
assembly or module, special care must be exercised to ensure each container is marked as
specified. Bar code markings shall be utilized.
6. NOTES
(This section contains information of a general or explanatory nature that may be helpful, but
is not mandatory.)
6.1 Intended use. The pump unit will be used primarily to pump fuel through a pipeline in
cold (-25 F) and hot (135 F) temperatures. The operating conditions will range from dry to
humid with frequent periods of blowing sand.
6.2 Acquisitions requirements. Acquisition documents should specify the following:
a. Title, number, and date of specification.
b. Issue of DODISS to be cited in the solicitation, and if required, the specific issue of
individual documents referenced (see 2.1.1 and 2.2).
c. When a first article is required for the first article inspection and approval
(see 3.2, 4.3 and 6.3).
d. When data for air transportability is required (see 3.17.3).
e. Color of finish coat if other than as specified (see 3.21).
f. When electromagnetic interference suppression is not required (see 3.24).
g. Time frame required for submission of first article pack (see 5.1 and 6.5).
h. Level of preservation and packing required (see 5.4 and 5.5).
i. Special marking required (see 5.6).
22

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.
9438 US Hwy 19N #311 Port Richey, FL 34668

Phone For Parts Inquiries: (727) 755-3260
Google +