 |
|||
|
|
|||
| ||||||||||
|
|  MIL-C-11015E
6.2 Acquisition requirements. Acquisition documents must specify the following:
(a) Title, number, and date of the specification.
(b) Issue of DoDISS to be cited in the solicitation, and if required, the specific issue of individual documents
referenced (see 2.1).
(c) Packaging requirements (see section 5).
(d) Lead length, if different from that specified (applicable to specification sheets MIL-C-11015/18,
MIL-C-11015/19, and MIL-C-11015/20). Lead length may be a minimum of .625 inch (15.88 mm) long or
1.00 inch (25.4 mm) long, as applicable (see 3.1), for use in tape & reel automatic insertion equipment.
6.3 Qualification. With respect to products requiring qualification, awards will be made only for products which
are at the time set for opening of bids, qualified for inclusion in the applicable qualified products list, whether or not
such products have actually been so listed by that date. The attention of the contractors is called to this
requirement, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal
Government, tested for qualification in order that they may be eligible to be awarded contracts or orders for the
products covered by this specification. The activity responsible for the qualified products list is the Defense Supply
Center Columbus, ATTN: DSCC/VQP, PO Box 3990, Columbus, OH 43216-5000.
6.4 Ambient operating conditions. Designers are cautioned to give consideration to the change in dielectric
constant with temperature, shelf aging, and electric-field intensity, and should recognize that the apparent insulation
resistance may vary with humidity and surface conditions.
6.5 Canceled styles. Several styles formerly covered by this specification have been canceled. Recommended
substitute items and applicable specification sheets are as listed in table IX.
6.5.1 Verification based upon established reliability parts. For the purpose of verification of qualification (see 4.5)
and conformance inspection (see 4.6), test data on identical items covered by MIL-PRF-39014 may be used.
TABLE IX. Cross-reference of substitute items.
Canceled style
Recommended substitute style
Style
Spec sheet
Style
Spec sheet
CK17
MIL-C-11015/20
CK15
MIL-C-11015/20
CK18 and CK19
MIL-C-11015/26
No Replacement
CK21
MIL-C-11015/1
No Replacement
CK26
MIL-C-11015/3
No Replacement
CK33
MIL-C-11015/5
CK22
MIL-C-11015/2
CK36
MIL-C-11015/6
No Replacement
CK37
MIL-C-11015/7
No Replacement
CK47
MIL-C-11015/8
CK27
MIL-C-11015/4
CK50
MIL-C-11015/16
CK61
MIL-C-11015/10
CK51
MIL-C-11015/17
CK63
MIL-C-11015/12
CK76 and CK77
MIL-C-11015/30
No Replacement
CK81
MIL-C-11015/15
No Replacement
CK90 and CK91
MIL-C-11015/22
No Replacement
CK95
MIL-C-11015/31
No Replacement
6.6 Standard capacitor types. Equipment designers should refer to MIL-HDBK-198, "Capacitors, Selection and
Use of," for a selection of standard capacitor types and values for new equipment design. Application information
concerning these capacitors is also provided in MIL-HDBK-198.
16
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals