 |
|||
|
|
|||
| ||||||||||
|
|  MIL-C-13874K
3 . 2 3 . 4 R i v e t e d c o n n e c t i o n s . R i v e t s s h a l l f i l l t h e h o l e s c o m p l e t e l y . T h e upset
rivet heads shall be full, neatly made, concentric with the rivet holes, and in
f u l l contact with the surface of the member and shall be in accordance with SAE
J492.
3.23.5 Machine work. Tolerances and gages for metal fits shall conform to the
limitations specified herein.
3 . 2 4 H u m a n f a c t o r s e n g i n e e r i n g . T h e air compressor shall comply with the
Special design emphasis shall be given to
d e s i g n criteria of MIL-STD-1472
MIL-STD-1472, general requirements (4), visual displays (5.2), controls (5.4),
l a b e l i n g ( 5 . 5 ) , a n t h r o p o m e t r y (5.6) , d e s i g n f o r m a i n t a i n e r ( 5 . 9 ) , a n d h a z a r d s a n d
safety (5.13), as applicable.
T h e noise produced by the air compressor shall conform to
3 . 2 5 Noise limits
M I L - S T D - 1 4 7 4 requirements, w i t h the exception of MIL-STD-1474, 5.2, 5.3, and 5.4,
w h e n t e s t e d i n a c c o r d a n c e w i t h 4 . 6 , 2 . 1 3 . T h e provisions of MIL-STD-1474, 4.3 and
4 . 4 shall be provided if and only if MIL-STD-1474, 5 . 1 . 1 . 2 p r o c e d u r e s h a v e b e e n
pursued and documented to the satisfaction of the procuring activity and written
permission to exceed the 85 dB(A) limit is obtained from the contracting officer.
I n accordance with MIL-STD-1474, 5 . 1 . 2 . 1 . 2 , t h e o p e r a t o r p o s i t i o n s h a l l b e d e f i n e d
as that point which is a horizontal distance of 18 inches from the pressure gauge.
Occasionally occupied positions are defined as those points that are 60 inches
Noise
a b o v e the ground and a horizontal distance of 39 inches from the unit
h a z a r d signs shall conform to MIL-STD-1474, 4.2 and 5.1.2.1.4.
4
QUALITY ASSURANCE PROVISIONS
4 . 1 R e s p o n s i b i l i t y f o r inspection. Unless otherwise specified in the contract
or purchase order, the contractor is responsible for the performance of all
i n s p e c t i o n r e q u i r e m e n t s ( e x a m i n a t i o n s a n d t e s t s ) a s s p e c i f i e d h e r e i n . E x c e p t as
otherwise specified in the contract or purchase order, the contractor may use his
own or any other facilities suitable for the performance of the inspection
r e q u i r e m e n t s s p e c i f i e d h e r e i n , u n l e s s disapproved by the Government. The
Government reserves the right to perform any of the inspections set forth in the
specification where such inspections are deemed necessary to ensure supplies and
services conform to prescribed requirements.
4 . 1 . 1 Responsibility for compliance All items shall meet all requirements of
sections 3 and 5. The inspection set forth in this specification shall become a
part of the contractor's overall inspection system or quality program. The
absence of any inspection requirements in the specification shall not relieve the
contractor of the responsibility of ensuring that all products or supplies
s u b m i t t e d to the Government for acceptance comply with all requirements of the
Sampling inspection, as part of manufacturing operations, is an
contract.
acceptable practice to ascertain conformance to requirements, however, this does
not authorize submission of known defective material, either indicated or actual,
n o r does it commit the Government to acceptance of defective material.
4.1.2 Component and material inspection. T h e c o n t r a c t o r i s r e s p o n s i b l e f o r
insuring that components and materials are manufactured, examined, and tested in
accordance with referenced specifications and standards, as applicable.
12
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals