 |
|||
|
Page Title:
Table 3. Group A inspection for device type 01-cont. |
|
||
| ||||||||||
|
|  TABLE III. Group A inspection for device type 01 Continued.
Terminal conditions 13/
Case A,B,D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Test limits
MIL-
Case C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Subgroup
Symbol
STD-883
Meas.
method
QD
QC
GND
QB
QA
NC
In A
Test No.
In BC
NC
NC
NC
R0(1)
R0(2)
VCC
Min
Max
Unit
terminal
9/
Fig 5
66
5.0 V
GND
GND
12/
9
12/
GND
12/
OUT 11/
IN
QA
10
MHz
FMAX
"
67
10/
"
"
"
OUT 11/
11/
"
11/
10/ 11/
"
QD
20
100
ns
TC = 25C
tPLH1
"
68
10/
"
"
"
OUT 11/
11/
"
11/
10/ 11/
"
QD
20
100
ns
tPHL1
9/
Fig 5
69
"
"
"
12/
10
12/
"
12/
OUT 11/
IN
QA
10
MHz
FMAX
"
70
10/
"
"
"
OUT 11/
11/
"
11/
10/ 11/
"
QD
20
115
ns
TC = 125C
tPLH1
"
71
10/
"
"
"
OUT 11/
11/
"
11/
10/ 11/
"
QD
20
115
ns
tPHL1
11
Same tests, terminal conditions and limits as for subgroup 10, except TC = -55C.
1/
Momentarily apply 2.4 V, then ground prior to taking measurements to set the device in desired state. Maintain ground for measurement.
2/
Apply 4.5 V pulse then ground prior to taking measurements to set the device in the desired state. Maintain ground for measurement.
A ≥ 2.0 V, B ≤ 0.8 V. Input voltages shown are the maximum for VIL and the minimum for VIH.
3/
4/
Only a summary of attributes data is required.
5/
Output voltages shall be either:
(a) H = 2.4 volts minimum and L = 0.4 volt maximum when using a high speed checker double comparator, or
(b) H ≥ 1.5 volts and L ≤ 1.5 volts when using a high speed checker single comparator.
6/ Input must be applied 3 times after R0 pulses.
7/ Input must be applied 2 times after R0 pulses.
8/ Input must be applied once after R0 pulses.
9/
FMAX, minimum limit specified is the frequency of the input pulse. The output frequency shall be one-half of the input frequency.
10/
Connect terminals together during test.
11/
See test figure 5 for terminal load.
12/
Omit specified loads for this test.
Terminal conditions (pins not designated may be H ≥ 2.0 V, or L ≤ 0.8 V, or open).
13/
14/
The limits shown shall be as follows:
Min/Max limits (ma) for circuit:
Test
A
B
C
D
E
IIL1
-0.4/-1.3
-0.4/-1.3
-0.3/-1.3
-0.7/-1.6
-0.7/-1.6
IIL2
-1.4/-3.2
-0.7/-3.2
-0.7/-3.2
-0.7/-3.2
-0.7/-3.2
IIL3
-1.4/-4.8
-0.7/-4.8
-0.7/-4.8
-1.4/-6.4
-1.4/-6.4
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals