Click here to make tpub.com your Home Page

Page Title: Acquisition requirements.
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 




img
MIL-M-38510/310D
5. PACKAGING
5.1 Packaging requirements. For acquisition purposes, the packaging requirements shall be as specified in the
contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these
personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements.
Packaging requirements are maintained by the Inventory Control Point's packaging activity within the Military
Department of Defense Agency, or within the Military Department's System Command. Packaging data retrieval is
available from the managing Military Department's or Defense Agency's automated packaging files, CD-ROM
products, or by contacting the responsible packaging activity.
6. NOTES
6.1 Intended use. Microcircuits conforming to this specification are intended for original equipment design
applications and logistic support of existing equipment.
6.2 Acquisition requirements. Acquisition documents should specify the following:
a.
Title, number and date of specification.
b.
Issue of DODISS to be cited in the solicitation, and if required, the specific issue of individual documents
referenced (2.1).
c.
Packaging requirements (see 5.1).
d.
Complete part number (see 1.2).
e.
Requirements for delivery of one copy of the quality conformance inspection data pertinent to the device
inspection lot to be supplied with each shipment by the device manufacturer, if applicable.
f.
Requirements for certificate of compliance, if applicable.
g.
Requirements for notification of change of product or process to contracting activity in addition to
notification to the qualifying activity, if applicable.
h.
Requirements for failure analysis (including required test condition of method 5003 of MIL-STD-883),
corrective action, and reporting of results, if applicable.
i.
Requirements for product assurance options.
j.
Requirements for special carriers, lead lengths, or lead forming, if applicable. These requirements shall
not affect the part number. Unless otherwise specified, these requirements will not apply to direct
purchase by or direct shipment to the Government.
k.
Requirements for "JAN" marking.
6.3 Superseding information. The requirements of MIL-M-38510 have been superseded to take advantage of the
available Qualified Manufacturer Listing (QML) system provided by MIL-PRF-38535. Previous references to MIL-M-
38510 in this document have been replaced by appropriate references to MIL-PRF-38535.
6.4 Qualification. With respect to products requiring qualification, awards will be made only for products which
are, at the time of award of contract, qualified for inclusion in Qualified Manufacturers List QML-38535 whether or not
such products have actually been so listed by that date. The attention of the contractors is called to these
requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal
Government tested for qualification in order that they may be eligible to be awarded contracts or purchase orders for
the products covered by this specification. Information pertaining to qualification of products may be obtained from
DSCC-VQ, 3990 E. Broad Street, Columbus, Ohio 43216-5000.
6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined
in MIL-PRF-38535, MIL-HDBK-1331, and as follows:
GND ...........................................
Ground zero voltage potential
IIN ................................................
Current flowing into an input terminal
VIC ...............................................
Input clamp voltage
VIN ...............................................
Voltage level at an input terminal
6.6 Logistic support. Lead materials and finishes (see 3.3) are interchangeable. Unless otherwise specified,
microcircuits acquired for Government logistic support will be acquired to device class B (see 1.2.2), lead material
and finish C (see 3.3). Longer length leads and lead forming shall not affect the part number.
19

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business