 |
|||
|
|
|||
| ||||||||||
|
|  MIL-P-18526A(SH)
Type of pressure regulating governor (see 3.5.2.1).
(k)
Electrical controller features, if other than as specified (see 3.5.5.1).
(1)
Performance characteristics:
(m)
(1) Rated capacity and range of capacity.
(2) Rated capacity and pressure.
(3) Fluid to be pumped (see 3.3.2.2).
(4) Viscosities.
(5) Temperature of fluid, normal, maximum, and
minimum (see 4.4.1.2).
(6) Suction lift.
(7) Special performance requirements, if any.
Number of sets of special tools (see 3.6.2.1).
(n)
Manuals required and whether complete information for electrical equip-
(0)
ment is required (see 3.7.2.1 and 3.7.2.3).
Quality assurance requirements (see 4.1.1).
(p)
Noise test and noise level limits (see 4.4.1.3).
(q)
Shock test requirements (see 4.4.3.8 and ordering data of MIL-S-901).
(r)
Vibration test requirements (see 4.4.3.10).
(s)
Ship type and fluid system in which units are to be installed.
(t)
Designation of manufacturer (pump or driver) responsible to the purchaser
(u)
for compatibility of pump and driver and operation of the assembled unit.
First article sample and technical data requirements (see 5.1).
(v)
Levels of preservation-packaging, and packing required (see 5.2) .
(w)
(x)
Special marking requirements (see 5.2.1) .
6.2.2 Data requirements. When this specification is used in a procurement which in-
vokes the provision of the "Requirements for Data" of the Armed Services Procurement Regula-
tions (ASPR) , the data identified below, which are required to be developed by the contractor
as specified on an approved Data Item Description (DD Form 1664) , and which are required to
be delivered to the Government, should be selected and specified on the approved Contract
Data Requirement List (DD Form 1423) and incorporated in the contract. When the provisions
of the "Requirements for Data" of the ASPR are not invoked in a procurement, the data re-
quired to be developed by the contractor and required to be delivered to the Government
should be selected from the list below and specified in the contract.
Data
Applicable DID
Paragraphs
requirements
Option
DI-E-7031
Level 3
Drawings, enqi-
3.7.1 and
Design activity designation - Contractor
neering and
3.7 .1.2.4
Drawing No. - Contractor
associated
Delivery of hard copy - Procuring activity
lists
3.7.2
Type I of MIL-M-15071
Manual. tech-
DI-M-2043
nical, pre-
liminary
Type I of MIL-M-15071
DI-M-2044
Manual, tech-
3.7.2
nical,
standard,
basic issue
UDI-T-23649
Test procedures
UDI-T-23729
Test reports
(Copies of data item descriptions required by the contractors in connection with speci-
fic procurement functions should be obtained from the procuring activity or as directed by
the contracting officer. Unless otherwise indicated, the issue in effect on date of invita-
tion for bids or request for proposal shall apply.)
6.2.2.1 The data requirements of 6.2.2 and any task in section 3, 4, or 5 of the spec-
ification required to be performed to meet a data requirement may be waived by the procuring/
purchasing activity upon certification by the offeror that identical data were submitted by
the offeror and accepted by the Government under a previous contract for identical item
procured to this specification. This does not apply to specific data which may be required
for each procurement regardless of whether an identical item has been supplied previously
(for example, test reports) .
6.3 With respect to products requiring qualification, awards will be made only for
products which are at the time set for opening of bids, qualified for inclusion in applicable
Qualified Products List QPL-18526 whether or not such products have actually been so listed
by that date. The attention of the contractors is called to these requirements, and manu-
facturers are urged to arrange to have the products that they propose to offer to the Fed-
eral Government tested for qualification in order that they may be eligible to be awarded
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals