 |
|||
|
Page Title:
Preservation-packaging, packing, and marking |
|
||
| ||||||||||
|
|  MIL-T-15108C(NAVY)
5.
PREPARATION FOR DELIVERY
5.1 Preservation-packaging, packing, and marking. Transformers shall be preserved-
#
packaged level A or C, packed A, B, or C as specified (see 6.2.1) and marked in accord-
ance with MIL-E-17555.
6.
NOTES
#
6.1 Intended use. Transformers are used in shipboard electrical power distribution
systems in order to step-down or step-up the voltage normally available.
6.2 Ordering data.
#
6.2.1 Procurement requirements.
Procurement documents should specify the following:
#
(a)
Title, number and date of this specification.
(b)
Voltage required (see 3.8.1).
(c)
KVA capacity required (see 3.8.3).
(d)
Duty (see 3.9).
(e)
Levels and requirements of preservation, packaging, and marking
(see 5.1).
When this specification is used in a procurement
#
6.2.2 Contract data requirements.
invoking the data requirement clause of the Armed Services Procurement Regulations (ASPR)
paragraph 7-104.9(n) and which incorporates a DD Form 1423 Contract Data Requirements List
(CDRL), the data requirements identified below will be developed as specified in the cited
Data Item Description (DID) and delivered in accordance with such CDRL. When the ASPR
provisions are not invoked, the data specified below shall be delivered in accordance with
contract requirements.
Specification
Data
Applicable
paragraph
requirements
Service
DID
Option
3.30.1
Drawings
SH
UDI-E-23174 Category A, F, and
G, form 2, type
II and III
------
4.1.1
Inspection system
SH
UDI-R-23574
------
4.5
Test reports
SH
UDI-T-23579
------
4.5
Test procedures
SH
UDI-T-23649
------
4.5
Calculations
SH
UDI-E-23213
(Copies of DID's required by the supplier in connection with specific procurement
functions should be obtained from the procuring activity or as directed by the contracting
officer. Unless otherwise indicated, the issue in effect on date of invitation for bids
or request for proposal shall apply.)
6.3 With respect to products requiring qualification, awards will be made only for
#
products which are at the time set for opening of bids, qualified for inclusion in applicable
Qualified Products List QPL-15108 whether or not such products have actually been so listed
by that date. The attention of the suppliers is called to this requirement, and manufacturers
are urged to arrange to have the products that they propose to offer to the Federal Govern-
ment tested for qualification in order that they may be eligible to be awarded contracts or
orders for the products covered by this specification. The activity responsible for the
Qualified Products List is the Naval Ship Engineering Center, Prince George's Center,
Center Building, Hyattsville, Maryland 20782, and information pertaining to qualification
of products may be obtained from that activity. Application for Qualification tests shall
be made in accordance with "Provisions Governing Qualification SD-6" (see 6.3.1).
6.3.1 Copies of "Provisions Governing Qualification SD-6" may be obtained upon
application to Commanding Officer, Naval Publications and Forms Center, 5801 Tabor Avenue,
Philadelphia, Pennsylvania 19120.
6.4 THE MARGINS OF THIS SPECIFICATION ARE MARKED "#m TO INDICATE WHERE CHANGES (ADDI-
TIONS, MODIFICATIONS, CORRECTIONS, DELETIONS) FROM THE PREVIOUS ISSUE HAVE BEEN MADE. THIS
WAS DONE AS A CONVENIENCE ONLY AND THE GOVERNMENT ASSUMES NO LIABILITY WHATSOEVER FOR ANY
INACCURACIES IN THESE NOTATIONS. BIDDERS AND CONTRACTORS ARE CAUTIONED TO EVALUATE THE
REQUIREMENTS OF THIS DOCUMENT BASED ON THE ENTIRE CONTENT IRRESPECTIVE OF THE MARGINAL
NOTATIONS AND RELATIONSHIP TO THE LAST PREVIOUS ISSUE.
User interest:.
Preparing activity:
Navy - OS
Navy - SH
(Project 6120-N016)
13
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals