 |
|||
|
Page Title:
Table II-A. Alternate marking (all styles) |
|
||
| ||||||||||
|
|  MIL-C-11272D
w/Amendment 1
TABLE II-A. Alternate marking (all styles).
Character
Significant
Capacitance (pF) and multiplier
units
Orange
Black
Green
Blue
Violet
Red
(x 0.1)
(x 1.0)
(x 10)
(x 100)
(x 1000)
(x 10,000)
A
10
1.0
10
100
1000
10,000
100,000
B
11
1.1
11
110
1100
11,000
110,000
C
12
1.2
12
120
1200
12,000
120,000
D
13
1.3
13
130
1300
13,000
130,000
E
15
1.5
15
150
1500
15,000
150,000
H
16
1.6
16
160
1600
16,000
160,000
I
18
1.8
18
180
1800
18,000
180,000
J
20
2.0
20
200
2000
20,000
200,000
K
22
2.2
22
220
2200
22,000
220,000
L
24
2.4
24
240
2400
24,000
240,000
N
27
2.7
27
270
2700
27,000
270,000
O
30
3.0
30
300
3000
30,000
300,000
R
33
3.3
33
330
3300
33,000
330,000
S
36
3.6
36
360
3600
36,000
360,000
T
39
3.9
39
390
3900
39,000
390,000
V
43
4.3
43
430
4300
43,000
430,000
W
47
4.6
47
470
4700
47,000
470,000
X
51
5.1
51
510
5100
51,000
510,000
Y
56
5.6
56
560
5600
56,000
560,000
Z
62
6.2
62
620
6200
62,000
620,000
3
68
6.8
68
680
6800
68,000
680,000
4
75
7.5
75
750
7500
75,000
750,000
7
82
8.2
82
820
8200
82,000
820,000
9
91
9.1
91
910
9100
91,000
910,000
4. VERIFICATION
4.1 Classification of inspections. The inspections specified herein are classified as follows:
a.
Qualification inspection (see 4.4).
b.
Conformance inspection (see 4.5).
4.2 Test equipment and inspection facilities. Test and measuring equipment and inspection facilities of sufficient
accuracy, quality and quantity to permit performance of the required inspection shall be established and maintained
by the supplier. The establishment and maintenance of a calibration system to control the accuracy of the
measuring and test equipment shall be in accordance with ANSI/NCSL Z540-1.
4.3 Inspections conditions and methods.
4.3.1 Inspection conditions. Unless otherwise specified herein, all inspections shall be performed in accordance
with the test conditions specified in the "GENERAL REQUIREMENTS" of MIL-STD-202.
4.3.2 Methods. Unless otherwise specified herein, all visual examinations shall be performed without
magnification other than those required to correct the eyesight. Radial lead type capacitors shall be tested with the
leads bent into the axial position.
4.4 Qualification inspection. Qualification inspection shall be performed at a laboratory acceptable to the
Government (see 6.2) on sample units produced with equipment and procedures normally used in production.
8
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals