Click here to make tpub.com your Home Page

Page Title: RF Command transmission.
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 




img
MIL-C-64025
code of 4.5.2.13 as specified by Drawing 9333026 for the current
group. After the FSD pulse sequence has been sent, verify that the RCU
displays "1 TRANSFER" in compliance with the requirements of 3.6.18
and 3,6.19.3.
For each group thru group 15,
4 . 5 . 2 . 1 7 G r o u p selection
test.
perform the following:  Press the GROUP ID key and verify that the
RCU displays "n  NONE" in compliance with the requirements of  3,6.17,
redo
3.6.18, and 3.6.18.1, where n is the current GROUP ID number;
4.5.2.16 substituting the current GROUP ID number for group 1 in that
test.
FSD  transfer  test.  Press the GROUP-ID key and
4.5.2.18 Invalid
verify the display response of "ALL" as per requirement 3.6.17. Press
.
the TRANSFER key and verify that the RCU displays "ALL INVALID'" in
compliance with the requirements of 3.6.19.4.
4.5.2.19 RF command transmission.  Connect a 50+5% ohm resistive
.
load from the ANTENNA to the RCU case. Press the GROUP ID key and
verify that the status of group 1 is displayed. Press the DEPLOY key
and verify that the RCU displays "DEPLOY  1" in compliance with the
requirements of 3.6.20.1. Press the XMIT switch and verify the
following.
4.5,2.19.1
Tune display.
Verify that the RCU displays "TUNING"
in compliance with the requirements of 3.6.20.2.
q
4.5.2.19.2  Transmit  display.  After the tuning sequence has
completed,  verify that the RCU displays "XMIT TUNE =  m" in  compliance
with the  requirements  of 3 .6.20,3 and that the tune number m is an
integer from 5 to 9.
4 . 5 . 2 . 1 9 . 3 R F o u t p u t  sequence.
Verify the RF waveform data with
the requirements of 3.6.20.4.
4.5.2.19.4 Group status update.  When transmission has
completed, verify that the RCU displays "1 DEPLOY" in compliance with
the requirements of 3.6.18 and 3.6.20.5. "
4.5.2.20
Command
group test.
Repeat
4.5.2.19
for
groups
2
thru
15.
4.5.2.21
Reset SD test.
Repeat  4.5.2.19  for  group  "ALL"  using
the RESET SD command key.
Verify that all 15 group status displays
conform  to  the  requirements  of  3.6.18  and  3.6.18.2.
4.5.2.22  Destruct
test.
Repeat 4.5.2.19 for group 1 using the
DESTRUCT command key.
4.5.2.23 Status
state  update  test.
Turn the unit power switch
off. Enter the STORE mode as per 4.5.2.11. Select a new SEND code as
per 4.5.2.10. Turn the unit power switch on and key in the correct
SEND code within the next 15 seconds. Verify the following tests in
accordance  with 3.6.18.2
139

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business