 |
|||
|
Page Title:
Table 3. Group A inspection for device type 05-cont. |
|
||
| ||||||||||
|
|  TABLE III. Group A inspection for device type 05 Continued. 1/
MIL-
Cases
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Subgroup
Symbol
STD-
A,B,D
Test limits
Measured
Unit
883
terminal
Case C
3
2
1
14
13
12
11
10
9
8
7
6
5
4
Min
Max
method
Q2
Q1
Clear 2
D2
Clock 2 Preset 2
Q2
GND
Q1
Preset 1
Test no.
Clock 1
D1
Clear 1
VCC
OUT
J
Clear1/Q1
GND
ns
200
IN
5.0 V
10
10
tPHL
3003 102 CKT A
TC=+125C
OUT
J
Clear1/Q1
"
"
120
IN
"
"
(Fig. 10) 102 CKT B
OUT
IN
"
"
200
J
"
"
103 CKT A
Preset 1/Q1
OUT
IN
"
"
120
J
"
"
103 CKT B
Preset 1/Q1
"
OUT
J
"
IN
200
"
"
104 CKT A
Clear2/Q2
"
OUT
J
"
IN
120
"
"
104 CKT B
Clear2/Q2
"
OUT
IN
"
J
200
"
"
105 CKT A
Preset 2/Q2
"
OUT
IN
"
J
120
"
"
105 CKT B
Preset 2/Q2
tPLH
3003 106 CKT A
IN
IN(G)
B
"
"
OUT
5.0 V
Clock1/Q1
"
150
"
(Fig. 11) 106 CKT B
IN
IN(G)
B
"
"
OUT
5.0 V
Clock1/Q1
"
85
"
107 CKT A
"
B
IN(G)
IN
5.0 V
OUT
"
Clock2/Q2
"
150
"
107 CKT B
"
B
IN(G)
IN
5.0 V
OUT
"
Clock2/Q2
"
85
"
108 CKT A
IN
IN(H)
B
"
"
OUT
5.0 V
Clock1/Q1
"
200
"
tPHL
108 CKT B
IN
IN(H)
B
"
"
OUT
5.0 V
"
120
"
Clock1/Q1
109 CKT A
"
B
IN(H)
IN
5.0 V
OUT
"
Clock2/Q2
"
200
"
109 CKT B
"
B
IN(H)
IN
5.0 V
OUT
"
Clock2/Q2
"
120
"
tPLH
3003 110 CKT A
IN
IN(G)
5.0 V
"
"
OUT
B
Clock1/Q1
"
150
"
(Fig. 12) 110 CKT B
IN
IN(G)
5.0 V
"
"
OUT
B
Clock1/Q1
"
85
"
111 CKT A
"
5.0 V
IN(G)
IN
B
OUT
"
Clock2/Q2
"
150
"
111 CKT B
"
5.0 V
IN(G)
IN
B
OUT
"
Clock2/Q2
"
85
"
tPHL
112 CKT A
IN
IN(H)
5.0 V
"
"
OUT
B
Clock1/Q1
"
200
"
112 CKT B
IN
IN(H)
5.0 V
"
"
OUT
B
Clock1/Q1
"
120
"
113 CKT A
"
5.0 V
IN(H)
IN
B
OUT
"
Clock2/Q2
"
200
"
113 CKT B
"
5.0 V
IN(H)
IN
B
OUT
"
Clock2/Q2
"
120
"
Same tests, terminal conditions, and limits as for subgroup 10, except TC=+55C
11
NOTE: A = normal clock pulse, B = momentary GND, then 4.5 V,
J = input pulse, tp ≥ 100 ns, PRR = 0 MHz, VOL = 0 V, VOH = 4.5 V.
Terminal conditions (pins not designated may be H ≥ 2.0 V, or L ≤ 0.8 V, or open).
1/
2/
Tests shall be performed in sequence.
3/
Input voltages shown are: A = 2.4 V minimum and B = 0.4 V maximum.
4/
Output voltages shall be either: (a) H = 2.4 V, minimum and L = 0.4 V, maximum when using a high speed checker double comparator; or
(b) H ≥ 1.5 V and L ≤ 1.5 V when using a high speed checker single comparator.
5/ fMAX, minimum limit specified is the frequency of the input pulse. The output frequency shall be one-half of the input frequency.
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals