Multiplexer, Time Division Digital TD-1069( )/G

• Multiplexer, Time Division Digital TD-1069( )/G
• Issues of documents-cont.
• Issues of documents-cont.
• Issues of documents-cont.
• Issues of documents-cont.
• TD-1069 performance requirements
• Data source tolerances
• Channel data rate programming
• Channel characteristics
• Table 1
• Channel output signal level
• Multiplexer output
• Demultiplexer input
• Syncronization and acquisition of bit count integrity
• Power supply
• Combination case
• Fault location - test facility
• Alarms (visible and audible)
• Audible signal On-Off switch
• Service conditions
• Shock (basic design)
• Bonds and grounds
• Cables and connectors
• Plug-in printed circuit cards
• Safety engineering
• Mean-time-to-repair (MTTRor MCT)
• Responsibility for inspection
• First article units
• Table 2. First article inspection
• Table 2. First article inspection-cont.
• Table 2. First article inspection-cont.
• Inspection covered by subsidiary documents
• Group A inspection
• Table 3. Group A inspection
• Table 4. Group B inspection
• Group B sampling plan
• Sampling for Group C inspection
• Reinspection of conforming Group C sample units
• Table 5. Group C inspection
• Service condition tests
• Humidity test
• Bounce, loose cargo test
• Electrical preconditioning inspection
• Marking of electrically preconditioned units
• Bounce preconditioning
• Data Source/Error Detector (DS/ED)
• Remote alarm test box
• Table 7. Standard Test Equipment
• Master oscillator frequency accuracy
• Channel balanced input signal sensitivity and output signal level
• Channel rate performance
• Teletypewriter channels and short circuit current
• Multiplexer output signal level
• Channel output waveshape
• Transmission format and multiplexer output waveshape
• Fault location and alarms
• Fault location and alarms-cont.
• Channel input impedance
• Channel output impedance
• Multiplexer longitudinal balance
• Demultiplexer input impedance
• Synchronization and acquisition of bit count integrity
• Power supply
• Power supply-cont.
• Interface characteristics
• Interface characteristics-cont.
• Table 8. Interface Characteristics Interconnection
• Interface characteristics-cont.
• Multiplexer interunit operating characteristics
• Channel data rate programming
• Channel data rate programming-cont.
• Unbalanced input signal sensitivity
• Unbalanced input signal sensitivity-cont.
• Maintenance of bit count integrity
• Resynchronization and re-acquisition of bit count integrity
• Fault location
• Extender panel
• External frequency source interface characteristics
• External frequency source interface characteristics-cont.
• Electrical subassembly test
• Electromagnetic Interference Test
• Reliability test conditions
• Failure definition
• Accept-reject criteria
• Inspection for dimensional interchangeability
• Nuclear air blast test
• Initial nuclear radiation test
• Unit packing
• Time Division Digital Multiplexer TD-1069 ( )/G
• Unitization
• Commercial packing
• Commercial marking
• Ordering data
• Growth colonization
• Location of operational inspection
• Figure 1. Output wave shaping (channels and group)
• Figure 2. Conditioned Diphase Modulated Output
• Figure 3a. General Test Set-up
• Figure 1b. Channel input sensitivity and output voltage
• Figure 3c. Channel waveshape and rate performance
• Figure 3d. Teletypewriter channel performance
• Figure 3e. Multiplexer output signal level
• Figure 3f. Demultiplexer input signal level
• Figure 4. Input impedance
• Figure 5. Output impedance
• Figure 6. Multiplexer longitudinal balance
• Figure 7. Demultiplexer longitudinal balance
• Figure 8. Bit Count integrity
• Figure 9. Power supply test set-up
• Figure 10a. Interface characteristics
• Figure 10b. TD-1069/TD-1065 compatibility
• Figure 11. Interunit Operating Characteristics
• Figure 12. Unbalanced Signal Channel Sensitivity
• Instructions
• Standardization Document Improvement Proposal
• Blank Page

Multiplexer, Time Division Digital TD-1069( )/G

Privacy Statement - Press Release - Copyright Information. - Contact Us